Solution Description

Product Description

Method for design chose
You should comprehend the pursuing at very first in buy to select the model of NMRV velocity reducer correctly:
– Loading problem.
– Velocity scope or ratio in software.
– Operating condition and environment.
– Set up place.

Determine working problem Coefficient K1 and revise coefficient K2.
– Ensure machinery load sorts A, B, C according to table 1.
– Get the doing work problem coefficient K1 from diagram 1 in accordance to turning time (hour/working day) and commence
frequency (time/hour).
– Examine doing work condition and decide on coefficient K2 from desk 2.

Desk 1 Machinery Load classification choice

Making use of scenario Instance Load sort
Uniform load Convey band (uniform conveying) A(Uniform load)
Reasonable Load Velocity changed conveying B(Reasonable load)
Severe Load Compressor, pulverizer, and so forth C(Extreme load)

Desk 2 Doing work situation coefficient K2

Ambient temperature Functioning condtion coefficient K2
-10C~30C 1
30C-40C one.1~1.2

Merchandise Parameters

NMRV worm gear motor

Design RV Model  RV Properties  Motor Design  Motor Properties  Interest
RV075 with 2.2KW NMRV075  L:198.5  two.2KW  Y100  Want to establish hollow or strong
RV090 with 2.2KW NMRV090  L:232.5  two.2KW  Y100 
RV063 with 1.5KW NMRV063  L:167  one.5KW  Y90L 
RV075 with 1.5KW NMRV075  L:198.5  1.5KW  Y90L 
RV090 with 1.5KW NMRV090  L:232.5  one.5KW  Y90L 
RV063 with 1.1KW NMRV063  L:167  one.1KW  Y90S 
RV075 with 1.1KW NMRV075  L:198.5  one.1KW  Y90S 
RV090 with 1.1KW NMRV090  L:232.5  1.1KW  Y90S 
RV050 with .75KW NMRV050  L:140  .75KW  Y80 
RV063 with .75KW NMRV063  L:167  .75KW  Y80 
RV075 with .75KW NMRV075  L:198.5  .75KW  Y80 
RV090 with .75KW NMRV090  L:232.5  .75KW  Y80 

Certifications

Business Profile

HangZhou Welldone Transmission Machinery Co., Ltd. specializes in producing different sorts of modest and medium-sized products, Three phase asynchronous motor, such as DC motor, AC motor, reducer, planetary reducer, servo reducer, and many others. We have professional gear tester (equipment all-spherical inspection), CZPT hardness tester, Rockwell hardness tester (examination hardness once more to ensure put on resistance), radial runout detection (detect motor working in and balance, so that the motor can lessen put on and no sounds throughout large-speed operation), endure voltage tester (detect leakage, higher than standard voltage, no leakage), inter flip tester, surge examination motor stator winding turn to flip insulation, thickened coil, same energy torque output, torque is increased.

The “Welldone” equipment reducer made by our firm sells nicely in provinces, municipalities and autonomous areas of the nation. It is broadly used in metallurgy, mining, lifting, transportation, petroleum, chemical, textile, pharmaceutical, meals, light-weight industry, grain, oil, feed and other industries, and is deeply trustworthy by customers.
Welcome new and previous buyers to visit and information.

FAQ

Q: How to select a appropriate motor or gearbox?
A: If you have motor photos or drawings to display us, or you have comprehensive technical specs, this kind of as, voltage, pace, torque, motor dimension, working mode of the motor, needed life time and sounds level and so on, you should do not be reluctant to permit us know, then we can advocate suited motor for every your ask for accordingly.

Q: Do you have a customized service for your regular motors or gearboxes?
A: Of course, we can customize for every your request for the voltage, pace, torque and shaft dimensions.

Q: What’s your direct time?
A: Normally speaking, our regular standard product will need 2-7days, a bit for a longer time for customized merchandise. It will rely on the distinct orders.

Click on below for deep communication.

Main Products

US $12-52
/ Piece
|
1 Piece

(Min. Order)

###

Application: Motor, Machinery, Marine
Function: Speed Changing, Speed Reduction, Speed Increase
Layout: Cycloidal
Hardness: Hardened Tooth Surface
Installation: Torque Arm Type
Step: Three-Step

###

Customization:

###

Using situation Example Load type
Uniform load Convey band (uniform conveying) A(Uniform load)
Moderate Load Speed changed conveying B(Moderate load)
Severe Load Compressor, pulverizer, etc C(Severe load)

###

Ambient temperature Working condtion coefficient K2
-10C~30C 1
30C-40C 1.1~1.2

###

Model RV Model  RV Properties  Motor Model  Motor Properties  Attention
RV075 with 2.2KW NMRV075  L:198.5  2.2KW  Y100  Need to determine hollow or solid
RV090 with 2.2KW NMRV090  L:232.5  2.2KW  Y100 
RV063 with 1.5KW NMRV063  L:167  1.5KW  Y90L 
RV075 with 1.5KW NMRV075  L:198.5  1.5KW  Y90L 
RV090 with 1.5KW NMRV090  L:232.5  1.5KW  Y90L 
RV063 with 1.1KW NMRV063  L:167  1.1KW  Y90S 
RV075 with 1.1KW NMRV075  L:198.5  1.1KW  Y90S 
RV090 with 1.1KW NMRV090  L:232.5  1.1KW  Y90S 
RV050 with 0.75KW NMRV050  L:140  0.75KW  Y80 
RV063 with 0.75KW NMRV063  L:167  0.75KW  Y80 
RV075 with 0.75KW NMRV075  L:198.5  0.75KW  Y80 
RV090 with 0.75KW NMRV090  L:232.5  0.75KW  Y80 
US $12-52
/ Piece
|
1 Piece

(Min. Order)

###

Application: Motor, Machinery, Marine
Function: Speed Changing, Speed Reduction, Speed Increase
Layout: Cycloidal
Hardness: Hardened Tooth Surface
Installation: Torque Arm Type
Step: Three-Step

###

Customization:

###

Using situation Example Load type
Uniform load Convey band (uniform conveying) A(Uniform load)
Moderate Load Speed changed conveying B(Moderate load)
Severe Load Compressor, pulverizer, etc C(Severe load)

###

Ambient temperature Working condtion coefficient K2
-10C~30C 1
30C-40C 1.1~1.2

###

Model RV Model  RV Properties  Motor Model  Motor Properties  Attention
RV075 with 2.2KW NMRV075  L:198.5  2.2KW  Y100  Need to determine hollow or solid
RV090 with 2.2KW NMRV090  L:232.5  2.2KW  Y100 
RV063 with 1.5KW NMRV063  L:167  1.5KW  Y90L 
RV075 with 1.5KW NMRV075  L:198.5  1.5KW  Y90L 
RV090 with 1.5KW NMRV090  L:232.5  1.5KW  Y90L 
RV063 with 1.1KW NMRV063  L:167  1.1KW  Y90S 
RV075 with 1.1KW NMRV075  L:198.5  1.1KW  Y90S 
RV090 with 1.1KW NMRV090  L:232.5  1.1KW  Y90S 
RV050 with 0.75KW NMRV050  L:140  0.75KW  Y80 
RV063 with 0.75KW NMRV063  L:167  0.75KW  Y80 
RV075 with 0.75KW NMRV075  L:198.5  0.75KW  Y80 
RV090 with 0.75KW NMRV090  L:232.5  0.75KW  Y80 

Cyclone Gearbox Vs Involute Gearbox

Whether you’re using a cycloidal gearbox or an involute gearbox for your application, there are a few things you should know. This article will highlight some of those things, including: cycloidal gearbox vs involute gearbox, weight, compressive force, precision, and torque density.helical gearbox

Compressive force

Several studies have been carried out to analyze the static characteristics of gears. In this article, the authors investigate the structural and kinematic principles of a cycloidal gearbox. The cycloidal gearbox is a gearbox that uses an eccentric bearing inside a rotating frame. It has no common pinion-gear pair, and is therefore ideal for a high reduction ratio.
The purpose of this paper is to investigate the stress distribution on a cycloidal disc. Various gear profiles are investigated in order to study the load distribution and dynamic effects.
Cycloidal gearboxes are subject to compression and backlash, which require the use of proper ratios for the bearing rate and the TSA. The paper also focuses on the kinematic principles of the reducer. In addition, the authors use standard analysis techniques for the shaft/gear and the cycloidal disc.
The authors previously worked on a rigid body dynamic simulation of a cycloidal reducer. The analysis used a trochoidal profile on the cycloidal disc periphery. The trochoidal profile is obtained from a manufacturing drawing and takes into account the tolerances.
The mesh density in the cycloidal disc captures the exact geometry of the parts. It provides accurate contact stresses.
The cycloidal disc consists of nine lobes, which move by one lobe per rotation of the drive shaft. However, when the disc is rotated around the pins, the cycloidal disc does not move around the center of gravity. Therefore, the cycloidal disc shares torque load with five outer rollers.
A low reduction ratio in a cycloidal gearbox results in a higher induced stress in the cycloidal disc. This is due to the bigger hole designed to reduce the material inside the disc.

Torque density

Several types of magnetic gearboxes have been studied. Some magnetic gearboxes have a higher torque density than others, but they are still not able to compete with the mechanical gearboxes.
A new high torque density cycloidal magnetic gearbox using Halbach rotors has been developed and is being tested. The design was validated by building a CPCyMG prototype. The results showed that the simulated slip torque was comparable to the experimental slip torque. The peak torque measured was a p3 = 14 spatial harmonic, and it corresponds to the active region torque density of 261.4 N*m/L.
This cycloidal gearbox also has a high gear ratio. It has been tested to achieve a peak torque of 147.8 Nm, which is more than double the torque density of the traditional cycloidal gearbox. The design incorporates a ferromagnetic back-support that provides mechanical fabrication support.
This cycloidal gearbox also shows how a small diameter can achieve a high torque density. It is designed with an axial length of 50mm. The radial deflection forces are not serious at this length. The design uses a small air gap to reduce the radial deflection forces, but it is not the only design option.
The trade-off design also has a high volumetric torque density. It has a smaller air gap and a higher mass torque density. It is feasible to make and mechanically strong. The design is also one of the most efficient in its class.
The helical gearing design is a newer technology that brings a higher level of precision to a cycloidal gearbox. It allows a servomotor to handle a heavy load at high cycle rates. It is also useful in applications that require smaller design envelopes.helical gearbox

Weight

Compared to planetary gearboxes, the weight of cycloidal gearboxes is not as significant. However, they do provide some advantages. One of the most significant features is their backlash-free operation, which helps them deliver smooth and precise movement.
In addition, they provide high efficiency, which means that servo motors can run at higher speeds. The best part is that they do not need to be stacked up in order to achieve a high ratio.
Another advantage of cycloidal gearboxes is that they are usually less expensive than planetary gearboxes. This means that they are suitable for the manufacturing industry and robotics. They are also suited for heavy-duty robots that require a robust gearbox.
They also provide a better reduction ratio. Cycloidal gears can achieve reduction ratios from 30:1 to 300:1, which is a huge improvement over planetary gears. However, there are few models available that provide a ratio below 30:1.
Cycloidal gears also offer more resistance to wear, which means that they can last longer than planetary gears. They are also more compact, which helps them achieve high ratios in a smaller space. The design of cycloidal gears also makes them less prone to backlash, which is one of the major shortcomings of planetary gearboxes.
In addition, cycloidal gears can also provide better positioning accuracy. In fact, this is one of the primary reasons for choosing cycloidal gears over planetary gears. This is because the cycloid disc rotates around a bearing independently of the input shaft.
Compared to planetary gearboxes, cycloidal gears are also much shorter. This means that they provide the best positioning accuracy. They are also 50% lighter, meaning that they have a smaller diameter.

Precision

Several experts have studied the cycloidal gearbox in precision reducers. Their research mainly focuses on the mathematical model and the method for precision evaluation of cycloidal gears.
The traditional modification design of cycloidal gears is mainly realized by setting various machining parameters and center position of the grinding wheel. But it has some disadvantages because of unstable meshing accuracy and uncontrollable tooth profile curve shape.
In this study, a new method of modification design of cycloidal gears is proposed. This method is based on the calculation of meshing backlash and pressure angle distribution. It can effectively pre-control the transmission accuracy of cycloid-pin gear. It can also ensure good meshing characteristics.
The proposed method can be applied in the manufacture of rotary vector reducers. It is also applicable in the precision reducer for robots.
The mathematical model for cycloidal gears can be established with the pressure angle a as a dependent variable. It is possible to calculate the pressure angle distribution and the profile pressure angle. It can also be expressed as DL=f(a). It can be applied in the design of precision reducers.
The study also considers the root clearance, the backlash of gear teeth and the profile angle. These factors have a direct effect on the transmission performance of cycloidal gear. It also indicates the higher motion accuracy and the smaller backlash. The modified profile can also reflect the smaller transmission error.
In addition, the proposed method is also based on the calculation of lost motion. It determines the angle of first tooth contacts. This angle is an important factor affecting the modification quality. The transmission error after the second cycloid method is the least.
Finally, a case study on the CZPT RV-35N gear pair is shown to prove the proposed method.helical gearbox

Involute gears vs cycloidal gears

Compared to involute gears, cycloidal gears have a lower noise, less friction, and last longer. However, they are more expensive. Cycloidal gears can be more difficult to manufacture. They may be less suitable for certain applications, including space manipulators and robotic joints.
The most common gear profile is the involute curve of a circle. This curve is formed by the endpoint of an imaginary taut string unwinding from the circle.
Another curve is the epicycloid curve. This curve is formed by the point rigidly attached to the circle rolling over another circle. This curve is difficult to produce and is much more expensive to produce than the involute curve.
The cycloid curve of a circle is also an example of the multi-cursor. This curve is generated by the locus of the point on the circle’s circumference.
The cycloid curve has the same diameter as the involute curve, but is tangentially curving along the circle’s diameter. This curve is also classified as ordinary. It has several other functions. The FE method was used to analyze the strain state of cycloidal speed reducers.
There are many other curves, but the involute curve is the most widely used gear profile. The involute curve of a circle is a spiraling curve traced by the endpoint of an imaginary tautstring.
Involute gears are a lot like a set of Lego blocks. They are a lot of fun to play with. They also have a lot of advantages. For example, they can handle center sifts better than cycloidal gears. They are also much easier to manufacture, so the cost of involute teeth is lower. However, they are obsolete.
Cycloidal gears are also more difficult to manufacture than involute gears. They have a convex surface, which leads to more wear. They also have a simpler shape than involute gears. They also have less teeth. They are used in rotary motions, such as in the rotors of screw compressors.
China RV Series Aluminum Material Worm Reduction Gearbox with Output Flange     small cycloidal gearboxChina RV Series Aluminum Material Worm Reduction Gearbox with Output Flange     small cycloidal gearbox
editor by czh 2023-01-05